Maserati Quattroporte Brake Job

Aug 1, 2012, 8:15 am
#1
Joined: Mar 11, 2007
Posts: 2,411
Another quick project thread. I have so many things unfinished, I get all excited when I can pound one out in a hurry. The QP had pretty thin pads, so it was time to replace before much more serious driving. Let's go!

Jacked up the car and removed wheels, calipers and rotors. Inspected and adjusted parking brake shoes. Caliper seals are good, pistons moved freely. Rotor showed no signs of heat stress, but had some scoring and glazing so they were checked for thickness. Sufficient mat'l to machine and still be over spec. Min thickness is .8661" or 22mm.

Also checked all suspension bushings and mounts, and cleaned up while in there.
Aug 1, 2012, 8:41 am
#2
Joined: Mar 11, 2007
Posts: 2,411
Depth micrometer is set at the factory spec min thickness. Rotors are Brembo, appear to be the original ones.
Aug 1, 2012, 8:43 am
#3
Joined: Mar 11, 2007
Posts: 2,411
Rotors back from the machine shop. Rears turned to .880 and .875 with a light cross hatch finish by Quinlin Automotive in Indy.
2006 Time Magazine's "Man Of The Year"
Aug 1, 2012, 8:46 am
#4
Joined: Mar 11, 2007
Posts: 2,411
There are two small pins that go thru the calipers and brake pads. Simply drive these out the back with a punch and the pads come out the back of the caliper by hand.
Aug 1, 2012, 8:49 am
#5
Joined: Mar 11, 2007
Posts: 2,411
Because the old pads are so much thinner than the new, the caliper pistons need to be pushed bach into their bores to allow space for the new. Off the car I use a c clamp, but this was easy to do with a screw driver as a pry bar to gently work then back, being careful not to poke a rubber seal.
Aug 1, 2012, 8:53 am
#6
Joined: Mar 11, 2007
Posts: 2,411
Slide new pads in place, install top pin, then hold spring clip in place while pushing the lower pin in from the back of the caliper. Seat them good with a small hammer, these pins are all that hold the pads in place. They click into place so you know when it is good.
Aug 1, 2012, 8:55 am
#7
Joined: Mar 11, 2007
Posts: 2,411
Assembled. Note carpeted wheel wells for sound deadening.
Aug 1, 2012, 8:57 am
#8
Joined: Mar 11, 2007
Posts: 2,411
Wheel cleaned up front and back.
2006 Time Magazine's "Man Of The Year"
Aug 1, 2012, 8:58 am
#9
Joined: Mar 11, 2007
Posts: 2,411
And done! Repeat 3 times.
Aug 1, 2012, 11:15 am
#10
Joined: Aug 5, 2007
Posts: 2,352
Congrats on finishing a project!
1983 Datsun 280ZXTurbo
Aug 1, 2012, 11:56 am
#11
Joined: Mar 11, 2007
Posts: 2,411
ZUL8TR wrote
Congrats on finishing a project!


Ta Daaa!!!

I was thinking, man, if I was not turning the rotors, as easy as the caliper pins are to R&R, swaping pads (like for track days) on this car would take about 60 seconds per corner. Sweet.
2006 Time Magazine's "Man Of The Year"
Aug 1, 2012, 12:07 pm
#12
Joined: Aug 5, 2007
Posts: 2,352
Yea, I was getting jealous looking at how easy that was. Mine involve blood, sweat and LOTS of swearing.

On the rears, I have to actually screw the calipers back with one of those pronged tools that really like to slip.
1983 Datsun 280ZXTurbo
Aug 4, 2012, 5:53 pm
#13
Joined: Sep 14, 2007
Posts: 609
Did you have to lube the back of the pads?
Aug 5, 2012, 1:46 pm
#14
Joined: Mar 11, 2007
Posts: 2,411
HoleInOne wrote
Did you have to lube the back of the pads?

These pad came with a self adhesive shim that got applied to the back of the pad. Peel and stick. Then a tiny film of anti sqeal on the back of that shim.
2006 Time Magazine's "Man Of The Year"
Aug 6, 2012, 4:45 am
#15
Joined: Jul 26, 2007
Posts: 520
Nice job Bill!
Jump to